How to Use Bare Speaker Wire ?

Nowadays, Bare speaker wire is widely used for connecting to spring clips or binding posts on speakers and receivers. The word “Bare” isn’t refers to the entire length of the wire. It is simply refer to the ends of the wire. And the Bare speaker wire doesn’t use connectors like the wire with spade connectors or banana plugs. In fact, they are just opposed to each other. When using, it is still important to disconnect the power from devices working on any wire is insulated, for the Bare speaker wire has the ability to carry an electrical charge. However, it is not especially difficult project to connecting a speaker wire. Of course, you still need to make some planning and care. Only in this way, you can get the best sound possible. To be friendly, there give you the way to Use Bare Speaker Wire. If you are just looking for it online, this will be perfect. During the way using Bare Speaker Wire, you need Wire cutters and Wire trippers or utility knife. Then, you can into the steps below.

Speaker Wire

Firstly, you need to select the right wire. At the beginning, you need measure the distance needed for your wire and chose a gauge suitable for the distance. Generally, a 16-gauge wire is appropriate for a distance less than 50 feet. If longer than 50 feet, a 14-gauge wire will be preferable for a lower gauge is thicker to carry current across longer distances adequately. Then, select a Class 2 rated wire which is good for running the wire through the home walls. while to walls of commercial buildings, you need select a Class 3 wire. All of these wires are verified by Underwriters Laboratories for using within walls with required shock-resistance and heat-resistance. If you are planning to run the wire across walls visible, a flat and paintable wire can be considered.

After getting the right wire, you can start to cutting and connecting the wire.
Step 1. Using wire cutters to cut the wire in an appropriate length that is required for your needs. Often, the longer a wire, the quality of the sound can be distorted. Of course, leave a few inches of slack is really a good idea. But using 20 feet of wire for a 10-foot run is not wise.

Step 2. Using wire strippers or a sharp utility knife to remove a half-inch of plastic protector or insulation from the end of the wire. During this process, you should ensure that you haven’t cut into the wire for higher frequencies can pass along the outside of the wire. This is often being called as “skin effect.” And cutting into the wire can also reduce the sound quality. To prevent the fraying, you need to twist three-eighths of an inch of the end of the bare wire.

Step 3. Connect the Speaker bare wire in a spring clip via pressing down on the grooved button to make its eye visible. Then, insert the end of the wire into that eye and move your finger from the button.

Step 4. Open a binding post through turning it counterclockwise. If the binding post with an eye, you can see it easily in the post when the screw rises. Insert the wire into that eye and screw down the post. While if there is no eye in the post, loop the wire around the base of the binding post in the clockwise direction and screw down the post to make it tighten against the wire. Otherwise, the post can become loose when you tighten it.

Where to buy Speaker Wire Canada

If you are planning to build home theater or sound system, it will be more likely for you to place speaker wire inside the wall or ceiling, thus, a UL-rated speaker wire with CL2 or CL3 labeled will be needed. Another indicator by confirming by its thickness or AWG, generally speaking, a 12-14 gauge is recommended for long wire run, high power application. For the short run, a 16 gauge wire will perform perfectly and more cost effective.

 

You might also like...

About

Andrew Lu - Marketing Manager - Shopper+ Networks Canada

Posted in Cables Tagged with: , , ,

Leave a Reply

Your email address will not be published. Required fields are marked *

*

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

Categories

Achives